800G OSFP 系列产品
400G OSFP 系列产品
400G QSFP112 系列产品
400G QSFP-DD 系列产品
200G 系列产品
100G 系列产品
40G 系列产品
25G 系列产品
10G 及其他速率产品
Featured
Hot-selling Sfp 10g Mm - 10GBASE-LR SFP+1310nm 10km Hi-Optel HSFP10-2323 module - Hi-optel
product detail
Descriptions The transceiver consists of two sections: The high performance a 1310nm DFB Laser, Transmitter and high sensitivity PIN integrated with a TIA. Receiver. A block diagram of the HSFP10-2323 SFP+ optical transceiver is shown below. The module is hot pluggable into the 20-pin connector. The high-speed electrical interface is based on low voltage logic, with nominal 100 Ohms differential impedance and AC coupled in the module. The optical output can be disabled by LVTTL logic high-level input of TX_Disable. Loss of signal (RX_LOS) output is provided to indicate the loss of an input optical signal of receiver. The receiver RATE_SELECT pin is not used by the transceiver. A 2-wire interface (SCL, SDA) is used for serial ID, digital diagnostics and other control /monitor functions. ● Absolute Maximum Ratings Parameter Symbol Min Max Unit Storage Temperature TST -40 +85 ℃ Supply Voltage VCC3 0.0 +3.6 V Relative Humidity RH 5 95 % ● Recommend Operation Environment Parameter Symbol Min Typ Max Unit Date Rate 10.3125 11.3 Gb/s Supply Voltage VCC +3.14 3.3 +3.47 V Supply Current ICC 300 mA Power Dissipation PD 800 1000 mW Operating Temperature TOP -40 25 +85 ℃ ● Optical Characteristics (Condition: Ta=TOP) Parameter Symbol Min Type Max Unit Note Transmitter Date Rate 10.3125 11.3 Gb/s Optical Wavelength λ 1260 1355 nm Average output power Po -6.5 0.5 dBm 1 Optical Extinction Ratio ER 3.5 dB 1 Optical Modulation Amplitude OMA -5.2 dBm Disabled Power Poff -30 dBm Side Mode Suppression Ratio SMSR 30 dB Dispersion penalty 3.2 dB Tx Jitter Txj Per 802.3ae requirements Receiver Date Rate 10.3125 11.3 Gb/s Optical Wavelength λ 1260 1355 nm Receiver Sensitivity R -14.4 dBm 2 Receiver Sensitivity in OMA R -12.6 Stressed Receiver Sensitivity in OMA R -10.3 dBm 2 Maximum Input Power PMAX 0.5 dBm LOS De-Assert LOSD -15 dBm LOS Assert LOSA -25 dBm LOS Hysteresis 0.5 4 dB Receiver Reflectance -12 dB Notes Note 1. Measured at 10.3125b/s with PRBS 231 – 1 NRZ test pattern. Note 2. Under the ER worst case, measured at 10.3125 Gb/s with PRBS 231 – 1 NRZ test pattern for BER< 1x10-12 ● Electrical Characteristics (Condition: Ta=TOP) Parameter Symbol Min Typ Max Unit Note Transmitter Differential input voltage swing VI 150 1600 mVpp 1 Common mode voltage tolerance 15 - - mV Transmit Disable Input H VIH 2.0 Vcc+0.3 V L VIL 0 0.8 V Transmit Enable Output H VOH 2.4 Vcc+0.3 V L VOL 0 0.4 V 2 Data Dependent Input Jitter DDJ 0.1 UI Data Input Total Jitter TJ 0.28 UI Input Differential Impedance Zin 80 100 120 Ω Receiver Differential output voltage swing 500 700 mVpp 3 LOS Output H VOH 2.4 Vcc+0.3 V 2 L VOL 0 0.4 V Rx Output Rise and Fall Time Tr/Tf 30 ps 20% to 80% Total Jitter TJ 0.7 UI Deterministic Jitter DJ 0.42 UI Output Differential Impedance Zon 80 100 120 Ω Note 1. TD+/- are internally AC coupled with 100Ω differential termination inside the module. Note 2. Tx Fault and Rx LOS are open collector outputs, which should be pulled up with 4.7k to 10kΩ resistors on the host board. Pull up voltage between 2.0V and Vcc+0.3V. Note 3. RD+/- outputs are internally AC coupled, and should be terminated with 100Ω (differential) at the user SERDES. Pin Assignment Diagram of Host Board Connector Block Pin Numbers and Name