800G OSFP 系列产品
400G OSFP 系列产品
400G QSFP112 系列产品
400G QSFP-DD 系列产品
200G 系列产品
100G 系列产品
40G 系列产品
25G 系列产品
10G 及其他速率产品
Featured
Hot sale 10g Sfp+ Rj45 Copper Transceiver - 10GBASE-SR SFP+ 850nm 300m Hi-Optel HSFP10-3831 module - Hi-optel
product detail
Descriptions Fiber type Minimum modal bandwidth @ 850 nm (MHz●km) Operatingra nge (meters) 62.5um MMF 160 2 to 26 200 2 to 33 50um MMF 400 2 to 66 500 2 to 82 2000 2 to 300 SFP+SR Operating Range for each Optical Fiber Type The transceiver consists of two sections: The high performance 850nm VCSEL transmitter and high sensitivity PIN integrated with a TIA. Receiver. A block diagram of the HSFP10-3831 SFP+ optical transceiver is shown below ● Absolute Maximum Ratings Parameter Symbol Min Max Unit Storage Temperature TST -40 +85 ℃ Supply Voltage VCC3 0 +3.6 V Relative Humidity RH 5 85 % ● Recommend Operation Environment Parameter Symbol Min Typ Max Unit Date Rate 10.3125 Gb/s Supply Voltage VCC +3.14 3.3 +3.47 V Supply Current ICC 180 200 mA Power Dissipation PD 0.8 W Operating Temperature TOP -5 25 +75 ℃ ● Transmitter Operating Characteristic-Optical, Electrical Parameter Symbol Min Typ Max Unit Ref. Side Mode Suppression Ratio SMSR 30 - dBm Average launch power of OFF transmitter Poff - -30 dBm Extinction Ratio ER 3.5 - dB 1 Transmitter Dispersion Penalty TDP - - 3.9 dB Operating Data Rate S 10.3125 Gbps Centre Wavelength λC 840 850 860 nm Spectrum Band Width (RMS) σ 0.45 nm Average Optical Power Pavg -7.3 - -1 dBm Optical Eye Mask Compliant with IEEE 802.3ae Input Differential Impedance ZIN 90 100 110 Ω TX Disable Disable 2.0 Vcc+0.3 V Enable 0 0.8 V TX Fault Fault 2.0 Vcc+0.3 V Normal 0 0.8 V Data Dependent Input Jitter DDJ 0.08 UI Data Input Total Jitter TJ 0.25 UI ● Receiver Operating Characteristic-Optical, Electrical Parameter Symbol Min Typ Max Unit Ref. Center Wavelength λr 850 nm Average receiver power PIN -11.1 dBm 2 Receiver Overload PMAX -1.0 dBm 2 Los Assert LosA -30 - dBm Los Dessert LosD -12 dBm Los Hysteresis LosH 0.5 2.5 5 dB Receiver Reflectance -12 dB 1 Output Differential Impedance PIN 90 100 110 Ω LOS High 2.0 Vcc+0.3 V Low 0 0.8 Rx Output Rise and Fall Time Tr/Tf 30 ps 20% to 80% Total Output Jitter TJ 0.7 UI Data Dependent Output Jitter DJ 0.42 UI Notes: Note 1. Measured at 10.3125b/s with PRBS 231 – 1 NRZ test pattern. Note 2. Under the ER worst case, measured at 10.3125 Gb/s with PRBS 231 – 1 NRZ test pattern for BER ● Control and Status I/O Timing Characteristics Parameter Symbol Min Max Unit Ref. TX Disable Assert Time t_off 10 µs 1 TX Disable Negate Time t_on 1 ms 2 Time to initialize including reset of TX_Fault t_init 300 ms 3 TX Fault Assert Time t_fault 100 µs 4 TX Disable to reset t_reset 10 µs 5 LOS Assert Time t_loss_on 100 µs 6 LOS Deassert Time t_loss_off 100 µs 7 Rate-Select Change Time t_ratesel 10 µs 8 Serial ID Clock Rate f_serial_clock 400 kHz Notes: 1. Time from rising edge of TX Disable to when the optical output falls below 10% of nominal. 2. Time from falling edge of TX Disable to when the modulated optical output rises above 90% of nominal. 3. From power on or negation of TX Fault using TX Disable. 4. Time from fault to TX fault on. 5. Time TX Disable must be held high to reset TX_fault. 6. Time from LOS state to RX LOS assert. 7. Time from non-LOS state to RX LOS deassert. 8. Time from rising or falling edge of Rate Select input until receiver bandwidth is in conformance with appropriate specification. Regulatory Compliance The HSFP10-383X complies with international Electromagnetic Compatibility and international safety requirements and standards (see details in Table following). Electrostatic Discharge (ESD) to the Electrical Pins MIL-STD-883E Method 3015.4 Class 1(>2000 V) Electromagnetic Interference (EMI) FCC Part 15 Class B EN55022 Class B (CISPR 22B) VCCI Class B Compatible with standards Laser Eye Safety FDA 21CFR 1040.10 and 1040.11 EN60950, EN (IEC) 60825-1,2 Compatible with Class 1 laser product.